|
MATERIAL SAFETY DATA SHEET
|
|
12-24-KEY812
1K SELF ETCHING PRIMER
|
|
HMIS CODES:
|
H
|
F
|
R
|
P
|
|
PRODUCT
NAME: 1K SELF
ETCHING PRIMER
|
|
|
2
|
2
|
1
|
G
|
|
PRODUCT
CODE: 12-24-KEY812
|
|
|
|
|
SECTION I - HAZARDOUS
INGREDIENTS/SARA III INFORMATION
|
|
|
|
VAPOR
PRESSURE
|
WEIGHT
|
|
REPORTABLE
COMPONENTS
|
CAS
NUMBER
|
mm Hg @
TEMP
|
PERCENT
|
|
Ethanol
|
64-17-5
|
44
|
20 C
|
60 - 65
|
|
|
OSHA TWA
1000 ppm, ACGIH TWA 1000 ppm
|
|
|
|
|
|
n-Butyl
Alcohol
|
71-36-3
|
4.4
|
20C
|
5 - 10
|
|
Isobutyl
Alcohol
|
78-83-1
|
8.8
|
20C
|
5 - 10
|
|
|
ACGIH TLV
50 ppm (TWA)
|
|
|
|
|
|
|
OSHA
(USA) PEL 50 ppm (TWA)
|
|
|
|
|
|
* Toluene
|
108-88-3
|
38
|
20 C
|
5 - 10
|
|
|
OSHA TWA
100 ppm
|
|
|
|
|
|
Methoxy-2-Propyl
Acetate
|
108-65-6
|
3.7
|
20 C
|
1 -5
|
|
|
None
established by OSHA or ACGIH as of 8/98
|
|
|
|
|
|
* Xylene,
mixed isomers
|
1330-20-7
|
38
|
20 C
|
1 - 5
|
|
|
OSHA TWA 100
ppm, STEL 150 ppm
|
|
|
|
|
|
*
Ethylbenzene
|
100-41-4
|
38
|
20 C
|
< 1
|
|
|
OSHA TWA
100 ppm, STEL 125 ppm
|
|
|
|
|
Indicates toxic chemical(s)
subject to the reporting requirements of section 313 of Title III and of 40 CFR
372. WARNING: DETECTABLE AMOUNTS OF A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA
TO CAUSE CANCER AND/OR BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM MAY BE PRESENT
IN THIS PRODUCT.
SECTION II - PHYSICAL/CHEMICAL CHARACTERISTICS
|
BOILING
RANGE: 150 F - 282F
|
SPECIFIC
GRAVITY (H20=1): 0.86
|
|
VAPOR
DENSITY: Heavier than air
|
EVAPORATION
RATE: Slower than n-Butyl Acetate
|
|
COATING
V.O.C.: 6.49 lb/gal
|
MATERIAL
V.O.C.: 6.38 lb/gal
|
|
SOLUBILITY
IN WATER: Non soluble
|
APPEARANCE
AND ODOR: Viscous liquid with ketone odor, color varies.
|
SECTION III - FIRE AND EXPLOSION HAZARD DATA
|
FLASH
POINT: 84.2 F
|
|
METHOD
USED: TCC
|
|
FLAMMABLE
LIMITS IN AIR BY VOLUME:
|
LOWER: 1.0
|
UPPER:
19.0
|
EXTINGUISHING MEDIA: FOAM, ALCOHOL FOAM, CO2, DRY
CHEMICAL, WATER FOG.
SPECIAL
FIREFIGHTING PROCEDURES: Respiratory equipment should be worn to
avoid inhalation of concentrated vapors. Water should not be used except as fog
to keep nearby containers cool.
UNUSUAL
FIRE AND EXPLOSION HAZARDS: Handle as flammable liquid. Vapors form
explosive mixture in air between upper and lower explosive limits which can be
ignited by many sources such as pilot lights, open flames, electrical motors
and switches.
SECTION IV -
REACTIVITY DATA
STABILITY: Stable
CONDITIONS
TO AVOID: Excessive
heat, poor ventilation, corrosive atmospheres, excessive age.
INCOMPATIBILITY
(Materials to avoid): Alkaline materials, strong acids, and oxidizing agents.
HAZARDOUS
DECOMPOSITION OR BYPRODUCTS: Carbon monoxide, carbon dioxide, oxides of nitrogen.
HAZARDOUS
POLYMERIZATION:
Will Not Occur.
SECTION V - HEALTH HAZARD DATA
INHALATION
HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Inhalation: Dizziness, breathing difficulty, headache &
loss of coordination.
SKIN AND EYE CONTACT
HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Eye contact: severe irritation, tearing, redness and
blurred vision.
SKIN
ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Skin contact: Can dry and defat skin
causing cracks, irritation, and dermatitis.
INGESTION
HEALTH RISKS AND SYMPTOMS OF EXPOSURE: Ingestion: Can cause gastrointestinal irritation, vomiting,
nausea, and diarrhea.
HEALTH
HAZARDS ( ACUTE AND CHRONIC ): ACUTE: Inhalation - Dizziness,
breathing difficulty, headaches, & loss of coordination. Eye Contact -
Severe irritation, tearing, redness, and blurred vision. Skin Contact -
Can dry and defat skin causing cracks, irritation, and dermatitis. Ingestion
- Can cause gastrointestinal irritation, vomiting, nausea, and diarrhea. CHRONIC: Repeated and prolonged overexposure
to solvents may lead to permanent brain and nervous system damage.
CARCINOGENICITY :
NTP CARCINOGEN: NO
IARC MONOGRAPHS: NO OSHA REGULATED: NO
MEDICAL CONDITIONS
GENERALLY AGGRAVATED BY EXPOSURE: Anesthesia, respiratory tract irritation, dermatitis,
nausea, and vomiting.
EMERGENCY AND FIRST AID
PROCEDURES: Inhalation
Overexposure - Move person to fresh air. If breathing stops, apply artificial respiration
and seek immediate medical attention. Eye Contact - Flush with large quantities
of water for 15 minutes. Skin Contact - Wash thoroughly with soap and water,
and see a doctor. Ingestion - DO NOT induce vomiting, can cause chemical
pneumonitis and pulmonary edema. Contact physician immediately.
SECTION
VI - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN
CASE MATERIAL IS RELEASED OR SPILLED: Eliminate ignition sources, provide good ventilation, dike
spill area and add absorbent earth or sawdust to spilled liquid.
WASTE
DISPOSAL METHOD: Collect
absorbent/spilled liquid mixture into metal container; cover and seal
container. Consult local, state, and federal hazardous waste regulations before
disposing into approved hazardous waste landfill. Obey relevant laws.
PRECAUTIONS
TO BE TAKEN IN HANDLING AND STORING: Use non-sparking utensils when handling this material. Avoid
hot metal surface. Use in cool, well ventilated areas. Keep containers closed
when not in use. Keep away from excessive heat and open flames.
OTHER
PRECAUTIONS: Smoking
in areas where this material is used should be strictly prohibited. Tools used
with this material should be made from aluminum, brass, or copper. Plastic
utensils should not be used.
SECTION
VII - CONTROL MEASURES
RESPIRATORY
PROTECTION: When
spraying this material use a fresh-air supplying respirator or a self-contained
breathing apparatus.
VENTILATION:
General mechanical
ventilation or local exhaust should be suitable to keep vapor concentrations
below TLV. Ventilation equipment must be explosion proof.
PROTECTIVE
GLOVES: Impermeable
chemical handling gloves for skin protection.
EYE
PROTECTION: Use
chemical safety glasses, goggles, and face shields for eye protection.
OTHER
PROTECTIVE CLOTHING OR EQUIPMENT: Use impermeable aprons and protective clothing whenever
possible to prevent skin contact. The use of head caps whenever possible is
strongly recommended.
WORK/HYGIENIC
PRACTICES: Eye
washes and safety showers in the workplace are recommended.
SECTION VIII
- DISCLAIMER
To the best of our
knowledge, the information contained herein is accurate, obtained from sources
believed by Cumberland Products Inc. to be accurate.